Devices for local smart homes

Smlight SLZB-06p7 CC2652P7 Zigbee coordinator with Ethernet, PoE, USB

The SLZB-06p7 Zigbee coordinator on the CC2652P7 chip, with a +20dB amp and +5dB antenna, holds a large whole-house mesh over Ethernet, PoE or USB.

The multiprotocol TI CC2674P10 radio with an ESP32-S3 host makes the SLZB-06p10 a coordinator that switches in firmware between Zigbee 3.0 and Thread, over Ethernet or USB-C.

Built on the EFR32MG24, the SLZB-06Mg24 runs Zigbee 3.0 and Thread on one radio, so your Home Assistant network reaches Matter-over-Thread too, not just Zigbee.

Built on the Silicon Labs EFR32MG21, the SLZB-06M is the 06-family pick for those on the Silabs stack — ZHA or deCONZ — with USB-C, Ethernet and PoE at once.

Smlight's original Zigbee 3.0 coordinator on the TI CC2652P, with USB-C, Ethernet and PoE: one device bridges your Zigbee mesh to Z2M or ZHA.

Four Matter 16A plugs in one box: a single kit covers the boiler, heater, office and kitchen of a whole home, each with its own energy meter.

Fires your gas or water boiler on a 42-slot schedule and by voice from Apple Home, Google Home and Alexa — no hub, just WiFi.

Guests and kids dim the light with a real button on the wall — the round Orb-DIM panel replaces the old switch, while app, voice and 1% scene control stay there for you.

Replace a worn double switch outright instead of hiding a relay behind it — the Orb-MW2 panel lands on the wall complete, with two independent 10 A channels.

A worn-out roller shutter button deserves replacing outright, and the Orb-RBS does exactly that — a finished 86×86 wall switch with physical up/down keys and Matter over Wi-Fi.

Evenings at a soft 20% and mornings at full power happen behind your existing switch — the MINI-DIM hides in the wall box and keeps the wall button working.

The 43 mm body with its tilting antenna takes just one server USB port, and the bundled 0.5 m extension keeps the coordinator radio clear of USB 3.0 noise.

One stop by the front door switches off the whole exit route — three independent channels drive the hallway, kitchen and bathroom lights from a single 3-gang plate.

Start your smart home where you sleep or work: the Orb-MW1 wall switch brings schedules and voice control to a single room, leaving the rest of the flat for later.

In the evening the chandelier rests — one key keeps just the soft sconce light, the other brings back full brightness for cleaning: two lighting zones in one 86×86 frame.

One Duo module behind a double rocker runs both lighting lines at once — chandelier and sconce keep their own wall keys yet switch independently via app or voice, 10 A per channel.

Behind the shutter buttons already on your wall, MINI-RBS slips into the round Ø60 mm flush box and gives the motor schedules, percentage control and Matter.

The smart layer hides flush in the wall: the WS01TPF-E replaces a regular socket in its mounting box, joins any Matter ecosystem over Wi-Fi and meters loads up to 16 A.

To guests it is just a wall switch — the key travels with the same mechanical click they expect, no touch glass or screens, while schedules and voice control work quietly inside.

Two imou CE2P Matter-over-Wi-Fi plugs, 16 A each, with energy metering: they join Apple Home, Google Home, Alexa and Home Assistant directly, no hub.

An RGB+CCT strip controller that speaks Matter over Wi-Fi directly and joins Apple Home, Google Home and Alexa with no Zigbee hub or Tuya gateway.

A boiler or a gate motor does not want 220 V from a relay — it waits for two signal wires to close, and the MINI-D dry contact does exactly that on app, schedule or voice command.

A regular relay will not fit behind the switch in a shallow flush box — the 39.5×33×16.8 mm MINIR4M will, 40% smaller than MINIR2 and with a Detach Relay mode on top.

Tucked behind an existing 2-gang switch, this Matter-over-Wi-Fi relay joins Apple Home, Google Home and Alexa directly, with no extra gateway to buy.