Devices for local smart homes

Smlight SLZB-06 Zigbee 3.0 coordinator — USB-C, Ethernet, PoE

Smlight's original Zigbee 3.0 coordinator on the TI CC2652P, with USB-C, Ethernet and PoE: one device bridges your Zigbee mesh to Z2M or ZHA.

Four Matter 16A plugs in one box: a single kit covers the boiler, heater, office and kitchen of a whole home, each with its own energy meter.

Four separate loads on one grey plate by the door: hallway light, stairs, terrace and a sconce each run their own line through a Zigbee gateway, no four-frame wall.

An open kitchen-living keeps three light lines — ceiling spots, the table lamp, the under-cabinet strip — on one white frame, every key on Zigbee and answering the local hub.

Touch the faceplate on the wall and the warm LEDs glide down for dinner: the MINI-ZBDIM-E swaps the old switch for a complete Zigbee dimmer, no hidden module buried in the box.

Guests and kids dim the light with a real button on the wall — the round Orb-DIM panel replaces the old switch, while app, voice and 1% scene control stay there for you.

The scenario is simple: on a leak-sensor alert the hub shuts the SWV-BSP valve, and on schedule it opens garden watering for a set water volume — all over Zigbee 3.0.

Sonoff TRVZB smart Zigbee 3.0 radiator valve with heating schedules, open-window detection, child lock and frost protection, controlled via eWeLink and Home Assistant.

Three light lines of an open kitchen-living sit on one grey feather-textured frame: ceiling, spots and table, each on its own touch key.

Two white keys on one frame each run their own zone over the home Zigbee mesh: kitchen and living room answer to a local hub, with the Wi-Fi router kept out of the path.

An old Chișinău flat leaves only the live and two load wires in the switch box, no neutral at all — the MINI-ZB2GS-L-E drops a glass Zigbee panel onto exactly that.

Add one more repeater to your Zigbee mesh: wired with neutral, the ZBM5 relays the network and answers a local Home Assistant — no cloud, no account.

Pull off the white rocker that ten years of fingers turned yellow and the MINI-ZB2GS-E glass panel takes its place: two Zigbee 3.0 channels, neutral required.

The cheapest moment to make shutters smart is while walls are still open: Orb-ZBRBS drops a Zigbee panel with key, percentages and scenes into a standard 86×86 box.

An evening dim-to-30% runs entirely inside the Zigbee mesh — no Wi-Fi, no cloud: the MINI-ZBDIM takes commands straight from the coordinator and relays the network as a router.

Replace a worn double switch outright instead of hiding a relay behind it — the Orb-MW2 panel lands on the wall complete, with two independent 10 A channels.

A worn-out roller shutter button deserves replacing outright, and the Orb-RBS does exactly that — a finished 86×86 wall switch with physical up/down keys and Matter over Wi-Fi.

Evenings at a soft 20% and mornings at full power happen behind your existing switch — the MINI-DIM hides in the wall box and keeps the wall button working.

The steel probe on its 1.5 m lead takes the cold and the liquid; the IP65 body with the LCD stays dry. The SNZB-02LD reads −40 to +115 °C — add a Zigbee 3.0 gateway for alerts.

Shower steam and balcony frost are exactly where the SNZB-02WD belongs: an IP65 case, a −20 to +60 °C range and a 2.2″ LCD; automations come alive once a Zigbee 3.0 hub joins.

The 43 mm body with its tilting antenna takes just one server USB port, and the bundled 0.5 m extension keeps the coordinator radio clear of USB 3.0 noise.

Dozens of Zigbee devices in Zigbee2MQTT or ZHA on a single stick: the TI CC2652P coordinator with +20 dBm output holds up to 200 nodes and reflashes into a router.

Unlike the ZBDongle-P built on the TI CC2652P, revision E runs a Silicon Labs EFR32MG21 with EmberZNet (EZSP) firmware, 20 dBm out of the box and Thread potential.

Pull the old mechanical switch off the wall and ZBMINIL2-E takes its place — a finished Zigbee switch with its own button that asks for no neutral in the box.