Devices for local smart homes

LinkNLink iSG Display Max — 10″ Smart Home Hub with Home Assistant

LinkNLink iSG Display Max touch hub: 10″ screen, built-in Home Assistant and Zigbee 3.0, Wi-Fi 2.4/5 GHz, Bluetooth, Matter — your whole smart home from one panel.

The white version of the NSPanel Pro: same 3.95" screen and Zigbee 3.0 hub as the black one, differing only by its white frame for light-coloured walls.

A local Zigbee 3.0 plus Wi-Fi hub in one touch panel: add Sonoff sensors and relays directly, run them from the screen and sync with Home Assistant.

Via the built-in Matter bridge, Zigbee sensors and relays show up in Apple Home, Google Home, Alexa and SmartThings; Ethernet RJ45 or 2.4 GHz Wi-Fi, up to 256 sub-devices.

A palm-sized fanless Linux mini-server: runs Home Assistant via MQTT and Zigbee2MQTT, with an onboard EFR32MG24 Zigbee/Thread radio and no separate Raspberry Pi.

With USB Type-C and USB-to-TCP/IP passthrough, the SLZB-MR3U hands its two radios — CC2674P10 for Zigbee, EFR32MG24 for Thread — straight to the PC or server running Z2M.

That heavy-headed feeling after hours in a closed room usually points to CO2 build-up, and the AirGuard CO2 tracks it with an NDIR sensor refreshing every 5 seconds.

Two radio SoCs in one box — CC2652P7 and EFR32MG21 — so the SLZB-MR1 runs a Zigbee network and a Thread network in parallel from a single PoE or USB-C coordinator.

A multiprotocol bridge that pulls Tuya Zigbee and Thread devices into Matter so the same gear answers Apple Home, Google and Alexa locally.

When the enemy is dust — traffic outside, a wood stove, fresh renovation — this AirGuard is the one: SAWF-07P reads PM2.5/PM10 every 2 seconds and alerts by light, sound and push.

The newest Silabs EFR32MG26 chip with the most memory in the 06 series makes the SLZB-06Mg26 a Zigbee, Thread and Matter coordinator on one board.

Schedules a warm floor across 42 weekly slots and answers Matter locally from Apple Home, Google Home and Alexa — no separate Tuya hub, just WiFi.

If your mesh keeps growing, the EFR32MG24 with 1536 KB Flash and 256 KB RAM keeps up — and a reflash turns the dongle into a Thread or Matter radio.

The multiprotocol TI CC2674P10 radio with an ESP32-S3 host makes the SLZB-06p10 a coordinator that switches in firmware between Zigbee 3.0 and Thread, over Ethernet or USB-C.

Built on the EFR32MG24, the SLZB-06Mg24 runs Zigbee 3.0 and Thread on one radio, so your Home Assistant network reaches Matter-over-Thread too, not just Zigbee.

Four Matter 16A plugs in one box: a single kit covers the boiler, heater, office and kitchen of a whole home, each with its own energy meter.

Fires your gas or water boiler on a 42-slot schedule and by voice from Apple Home, Google Home and Alexa — no hub, just WiFi.

Guests and kids dim the light with a real button on the wall — the round Orb-DIM panel replaces the old switch, while app, voice and 1% scene control stay there for you.

With an IC behind every one of its 150 LEDs, the Sonoff L3 Pro shows several colours at once and runs chasing gradients along all 5 metres — the 5V adapter is sold separately.

Replace a worn double switch outright instead of hiding a relay behind it — the Orb-MW2 panel lands on the wall complete, with two independent 10 A channels.

A worn-out roller shutter button deserves replacing outright, and the Orb-RBS does exactly that — a finished 86×86 wall switch with physical up/down keys and Matter over Wi-Fi.

Evenings at a soft 20% and mornings at full power happen behind your existing switch — the MINI-DIM hides in the wall box and keeps the wall button working.

The 43 mm body with its tilting antenna takes just one server USB port, and the bundled 0.5 m extension keeps the coordinator radio clear of USB 3.0 noise.

One stop by the front door switches off the whole exit route — three independent channels drive the hallway, kitchen and bathroom lights from a single 3-gang plate.