Devices for local smart homes

Roborock Saros Z70 Robot Vacuum with OmniGrip Mechanical Arm (Black)

The OmniGrip arm tidies objects under 300 g, while 22000 Pa suction and spinning mops handle the floor for you.

LinkNLink iSG Display Max touch hub: 10″ screen, built-in Home Assistant and Zigbee 3.0, Wi-Fi 2.4/5 GHz, Bluetooth, Matter — your whole smart home from one panel.

The white version of the NSPanel Pro: same 3.95" screen and Zigbee 3.0 hub as the black one, differing only by its white frame for light-coloured walls.

A local Zigbee 3.0 plus Wi-Fi hub in one touch panel: add Sonoff sensors and relays directly, run them from the screen and sync with Home Assistant.

Drives your existing roller blind from a 35 mm in-tube motor with 8 N·m torque. Zigbee 3.0, Aqara Home app, Siri/Google/Alexa. Hub required.

Via the built-in Matter bridge, Zigbee sensors and relays show up in Apple Home, Google Home, Alexa and SmartThings; Ethernet RJ45 or 2.4 GHz Wi-Fi, up to 256 sub-devices.

A palm-sized fanless Linux mini-server: runs Home Assistant via MQTT and Zigbee2MQTT, with an onboard EFR32MG24 Zigbee/Thread radio and no separate Raspberry Pi.

With USB Type-C and USB-to-TCP/IP passthrough, the SLZB-MR3U hands its two radios — CC2674P10 for Zigbee, EFR32MG24 for Thread — straight to the PC or server running Z2M.

That heavy-headed feeling after hours in a closed room usually points to CO2 build-up, and the AirGuard CO2 tracks it with an NDIR sensor refreshing every 5 seconds.

Two radio SoCs in one box — CC2652P7 and EFR32MG21 — so the SLZB-MR1 runs a Zigbee network and a Thread network in parallel from a single PoE or USB-C coordinator.

A multiprotocol bridge that pulls Tuya Zigbee and Thread devices into Matter so the same gear answers Apple Home, Google and Alexa locally.

When the enemy is dust — traffic outside, a wood stove, fresh renovation — this AirGuard is the one: SAWF-07P reads PM2.5/PM10 every 2 seconds and alerts by light, sound and push.

The newest Silabs EFR32MG26 chip with the most memory in the 06 series makes the SLZB-06Mg26 a Zigbee, Thread and Matter coordinator on one board.

If your mesh keeps growing, the EFR32MG24 with 1536 KB Flash and 256 KB RAM keeps up — and a reflash turns the dongle into a Thread or Matter radio.

The SLZB-06p7 Zigbee coordinator on the CC2652P7 chip, with a +20dB amp and +5dB antenna, holds a large whole-house mesh over Ethernet, PoE or USB.

The multiprotocol TI CC2674P10 radio with an ESP32-S3 host makes the SLZB-06p10 a coordinator that switches in firmware between Zigbee 3.0 and Thread, over Ethernet or USB-C.

Built on the EFR32MG24, the SLZB-06Mg24 runs Zigbee 3.0 and Thread on one radio, so your Home Assistant network reaches Matter-over-Thread too, not just Zigbee.

Built on the Silicon Labs EFR32MG21, the SLZB-06M is the 06-family pick for those on the Silabs stack — ZHA or deCONZ — with USB-C, Ethernet and PoE at once.

Smlight's original Zigbee 3.0 coordinator on the TI CC2652P, with USB-C, Ethernet and PoE: one device bridges your Zigbee mesh to Z2M or ZHA.

Four Matter 16A plugs in one box: a single kit covers the boiler, heater, office and kitchen of a whole home, each with its own energy meter.

Four separate loads on one grey plate by the door: hallway light, stairs, terrace and a sconce each run their own line through a Zigbee gateway, no four-frame wall.

Fires your gas or water boiler on a 42-slot schedule and by voice from Apple Home, Google Home and Alexa — no hub, just WiFi.

An open kitchen-living keeps three light lines — ceiling spots, the table lamp, the under-cabinet strip — on one white frame, every key on Zigbee and answering the local hub.

Touch the faceplate on the wall and the warm LEDs glide down for dinner: the MINI-ZBDIM-E swaps the old switch for a complete Zigbee dimmer, no hidden module buried in the box.